Search Results

The technique of evaporating fuel by localized heating before entering the intake manifold is evaluated as a means of improving A/F ratio control. Techniques currently in use are briefly discussed, and attempts to analyze fuel evaporation in S.I. engines are reviewed. A test fixture which includes all the essential features of production feasible hardware is used to develop a basis of understanding for the evaporation process. Tests are conducted on a flow bench using water as “fuel”, and on an engine using isooctane and gasoline. A heat-mass transfer analogy is described and used to predict evaporation rates for water and isooctane. Predicted and measured rates are compared for both bench and engine tests. Engine tests with gasoline show the ability of the test configuration to evaporate all part throttle fuel flow before it enters the intake manifold.

The design requirements for the frame as a load carrying member are discussed in relationship to a highway truck and its basic vehicle package. The theoretical and experimental procedures are given in detail to demonstrate the techniques for frame design. The features of a method to laboratory test a frame with correlation to service miles is discussed.

In the current design process, the designer generates the detailed geometry of the component based on experience. Prototypes of this design are built and tested to verify the performance. This design - build - test iterative process is continued until performance targets/criteria are met. Computer Aided Engineering is often used to verify the design. This paper presents a new product development process to substantially reduce the number of design - analysis - build - test iterations. This Upfront Analysis Driven Design process incorporates several state of the art technologies in finite element structural analysis, optimization, and Computer Aided Design. This process ensures a near optimum design in the first design level itself.

Nonlinear finite element analysis has been applied to determine the conditions conducive to seal system aspiration. Aspiration noise occurs and propagates into the passenger compartment of a vehicle when there exists a gap between the seal and sealing surface due to pressure differential between the vehicle interior and exterior. This pressure differential is created by the vehicle movement which reduces the pressure acting on the exterior surface of the vehicle, and it is on the order of , where ρ and U∞ are the density of air and vehicle speed, respectively. The pressure difference is also created by turning on the climate control system which pressurizes the passenger cavity. Since aspiration increases door seal cavity noise level and creates a direct noise transmission path without any significant transmission loss, the presence of an aspiration noise source can dominate the vehicle interior noise level if it is close to the driver or passenger's ears.

The study presented in this paper is concerned with the application of a finite element based technique to deal with crankshaft-crankcase interaction. A finite element model of the crankshaft and the crankcase was developed and appropriately reduced. This model was used for a crankshaft optimization, strategy to analyse related effects on the NVH performance with focus on main bearing acceleration. The crankshaft and the cylinder block were modelled using beam and shell elements with structural and dynamic properties correlated up to 1600 Hz. The interaction between crankshaft and the cylinder block was represented by using non-linear properties. Applying this model, the dynamic crankshaft and engine block behaviour and repercussion on NVH performance was analysed by investigating main bearing acceleration.

Imposing tensile stress on an edge of a sheet metal blank is a common condition in many sheet metal forming operations, making edge formability a very important factor to consider. Because edge formability varies greatly among different materials, cutting methods (and their control parameters), it is very important to have access to an experimental technique that would allow for quick and reliable evaluation of edge formability for a given case. In this paper, two existing techniques are compared: the hole expansion test and the tensile test. It is shown that the hole expansion test might not be adequate for many cases, and is prone to overestimating the limiting strain, because the burr on the sheared edge is typically smaller than what is observed in production. The tensile test represents an effective alternative to the hole expansion test. Advantages and disadvantages of each case are discussed.

Applications of the finite element method for analysis of partial and complete body structures are described. Ford Motor Co.'s version of the Structural Analysis and Matrix Interpretive System (SAMIS) computer program provides the capability for a static analysis of structures with over 10,000 degrees of freedom. Special modeling techniques for spot welded structural components have been investigated. Also, methods for quick input data development and effective visual displays of output data are discussed.

The object of this paper is to develop a random vibration laboratory test specification for automotive subsystems using the Power Spectral Density (PSD) method. This development is based on the 150k mile field data collected from vehicle proving grounds. The simulated vibration bench test will be used to simulate the energy of the 150k mile field data. The developed specification will include 3 axis random vibration profiles of appropriate duration. The Power Spectral Density method converts the time-domain field data into the frequency-domain data. The Enveloped Energy method groups the similar road PSD profiles to produce a generic PSD profile. The Inverse Law allocates an adjusted duration to the desired PSD energy level. The Road Test Specification provides the duration time for the developed bench test. The n-Soft tool [1] is utilized for data reduction analysis. The Bench Test Specification of the Fuel subsystem is a pilot for this development.

In order to understand the crush behavior of complex structural system such as a vehicle, one must first acquire the knowledge of crush characteristics of structural components that constitute the system and control its crush performance. In this paper, the crush strength characteristics and modes of collapse of thin walled circular columns are mathematically formulated. The formulation is based on the stability of shell structure subjected to axial crush, where various stages of collapse are identified and crush characteristics pertinent to column design are quantified. The effect of column size and the material properties on the collapse stability and crush strength characteristics of thin walled shell components are discussed. The size and number of folds for the axisymmetric “ring” mode and the nonsymmetric “diamond” mode are determined.

This paper describes the development and key features of a bar code based, computerized gas cylinder inventory and record keeping system developed by Ford Motor Company's Gas Standards Laboratory. The paper will demonstrate how bar code technology is being utilized to track compressed gas cylinders efficiently and accurately. It will also describe the link between bar code technology and a data base that was developed using a fourth generation computer language. The implementation of this bar code/data base system has significantly increased data accessibility, improved data quality, reduced training time and increased the efficiency and flexibility of the data reporting process.

Little information is available concerning the bending fatigue behavior of helical gears with tall thin teeth and high contact ratios, particularly for planetary pinions which are subjected to fully reversed loading. The most common methods to acquire gear bending fatigue data are either through a four-square recirculating power arrangement or unidirectional single tooth bending experiments on standardized spur gears. There are some advantages to these test methods, but they generally do not represent actual operating conditions of a planetary gear environment. The purpose of this study was to develop a bending fatigue test for planetary pinions in automatic transmissions which would better represent actual operating conditions. The new testing procedure was used to evaluate the bending fatigue behavior of three gear steel/processing combinations. The results from the planetary gear testing is compared with laboratory four-point bending experiments.

Structural adhesives are widely used across the automotive industry for several reasons like scale-up of structural performance and enabling multi-material and lightweight designs. Development engineers know in general about the effects of adding adhesive to a spot-welded structure, but they want to quantify the benefit of adding adhesives on weight reduction or structural performance. A very efficient way is to do that by applying analytical tools. But, in most of the relevant non-linear load cases the classical lightweight theory can only help to get a basic understanding of the mechanics. For more complex load cases like full car crash simulations, the Finite Element Method (FEM) with explicit time integration is being applied to the vehicle development process. In order to understand the benefit of adding adhesives to a body structure upfront, new FEM simulation tools need to be established, which must be predictive and efficient.

The exhaust blowdown pulse from each cylinder of a multi-cylinder engine propagates through the exhaust manifold and can affect the in-cylinder pressure of other cylinders which have open exhaust valves. Depending on the firing interval between cylinders connected to the same exhaust manifold, this blowdown interference can affect the exhaust stroke pumping work and the exhaust pressure during overlap, which in turn affects the residual fraction in those cylinders. These blowdown interference effects are much greater for a turbocharged engine than for one which is naturally aspirated because the volume of the exhaust manifolds is minimized to improve turbocharger transient response and because the turbines restrict the flow out of the manifolds. The uneven firing order (intervals of 90°-180°-270°-180°) on each bank of a 90° V8 engine causes the blowdown interference effects to vary dramatically between cylinders.

Modern project management including brake testing includes the exchange of reliable results from different sources and different locations. The ISO TC22/SWG2-Brake Lining Committee established a task force led by Ford Motor Co. to determine and analyze root causes for variability during dynamometer brake performance testing. The overall goal was to provide guidelines on how to reduce variability and how to improve correlation between dynamometer and vehicle test results. This collaborative accuracy study used the ISO 26867 Friction behavior assessment for automotive brake systems. Future efforts of the ISO task force will address NVH and vehicle-level tests. This paper corresponds to the first two phases of the project regarding performance brake dynamometer testing and presents results, findings and conclusions regarding repeatability (within-lab) and reproducibility (between-labs) from different laboratories and different brake dynamometers.

The ISO TC22/SWG2 - Brake Lining Committee established a task force to determine and analyze root causes for variability during dynamometer brake performance testing. SAE paper 2010-01-1697 “Brake Dynamometer Test Variability - Analysis of Root Causes” [1] presents the findings from the phases 1 and 2 of the “Test Variability Project.” The task force was created to address the issue of test variability and to establish possible ways to improve test-to-test and lab-to-lab correlation. This paper presents the findings from phase 3 of this effort-description of factors influencing test variability based on DOE study. This phase concentrated on both qualitative and quantitative description of the factors influencing friction coefficient measurements during dynamometer testing.

This paper presents the design and operation of a new stepped bore master cylinder (fast-fill) which also integrates the rear brake proportioning valves and brake failure warning device in one major assembly. This design optimizes weight, performance and package together with several unique design features. It incorporates a combination of a plastic reservoir, permanent mold aluminum body, steel pistons, and minaturized steel proportioning valves resulting in a significant weight and cost reduction versus equivalent hydraulic actuation systems.

All automotive brake linings have mechanical strength and thermal expansion properties which vary with orientation. This paper describes laboratory equipment and test procedures which characterize lining strength and expansion behavior, using small specimens. A benchtop testing device is introduced which can be used to perform shear and tensile tests on lining samples and singly-riveted lining assemblies. Results are presented for a representative group of production and experimental linings. Applications are discussed.

A stochastic simulation based on the Monte-Carlo method was developed to re-target gap bulk density (GBD) in ceramic catalytic converters. The combined effect of manufacturing tolerances, shell spring back and thermal expansion was analyzed by this model. Shell spring back during the canning process was calculated using Finite Element Analysis (FEA). Thermal shell expansion was obtained using can deformation data from the Key-Life Test (KLT). An example of optimized GBD that provides a robust and manufacturable design is also presented.

Flow fields generated during the intake stroke of a 4-stroke I.C. engine are studied experimentally using water analog simulation. The fluid is seeded by small flow tracer particles and imaged by two digital cameras at BDC. Using a 3-D Particle Tracking Velocimetry technique recently developed, the 3-D motion of these flow tracers is determined in a completely automated way using sophisticated image processing and PTV algorithms. The resulting 3-D velocity fields are ensemble averaged over a large number of successive cycles to determine the mean characteristics of the flow field as well as to estimate the turbulent fluctuations. This novel technique was applied to three different cylinder head configurations. Each configuration was run for conditions simulating idle operation two different ways: first with both inlet ports open and second with only the primary port open.

The customer's perception of diesel sounds is receiving more attention since diesel engines are being used more frequently in recent years. This paper summarizes the results of a study investigating the sound quality of diesel idle sounds in eight vans and light trucks. Subjective evaluations were conducted both in the US and the UK so that a comparison could be made. Paired comparison of annoyance and semantic differential subjective evaluation techniques were used. Correlation analysis was applied to the subjective evaluation results to determine annoying characteristics. Subjective results indicated that most annoyance rankings were similar for both the US and UK participants, with some specific differences. Correlation of objective measures to annoyance indicated a high correlation to ISO 532B loudness, dBA and kurtosis in the 1.4 kHz to 4 kHz range (aimed at quantifying the impulsiveness perception).